Skip to content

elato/sidekick

Pocket-sized always-listening AI companion. Dual MEMS mics, class-D audio, ESP32-S3 and a two-hour print for the shell.

v2.1.0esp32-s34-layer · 46×32 mm$31.40 BOM2h buildCERN-OHL-S-2.0updated 12 days ago
Remix

Build log22 reports

  • theov2.1.023 days ago30.192h 6m

    Running for three weeks continuously, no issues.

  • amarav2.1.01 months ago32.864h 7m

    Assembled by JLCPCB, only the connectors by hand. Total came in under budget.

    • swapped LDO for AP2112K
    • 3D-printed lid in PETG
  • luciav2.1.01 months ago34.453h 1m

    One cold joint on the ground pad — needed flux and a bigger tip.

  • sam-kv2.0.01 months ago47.452h 13m

    Printed the enclosure in PETG at 0.2mm, fits with no sanding.

  • dmitriv2.0.01 months ago39.263h 56m

    Boot loop until I flashed with the 2.1 partition table. Docs could say this louder.

  • sam-kv2.0.01 months ago37.313h 27m

    Running for three weeks continuously, no issues.

  • ilyav2.1.02 months ago42.833h 35m

    Printed the enclosure in PETG at 0.2mm, fits with no sanding.

  • amarav2.1.02 months ago39.463h 18m

    Running for three weeks continuously, no issues.

  • theov2.1.03 months ago28.724h 9m

    One cold joint on the ground pad — needed flux and a bigger tip.

  • tomasv2.0.03 months ago40.084h 30m

    USB enumeration failed until I added the 5.1k CC resistors. Check the errata.

  • nilsv2.1.03 months ago35.154h 9m

    Substituted a cheaper mic; SNR is noticeably worse but usable.

  • priyav2.1.03 months ago40.913h 56m

    Substituted a cheaper mic; SNR is noticeably worse but usable.

    • swapped LDO for AP2112K
    • 3D-printed lid in PETG
  • obiv2.0.03 months ago45.473h 45m

    Boot loop until I flashed with the 2.1 partition table. Docs could say this louder.

    • swapped LDO for AP2112K
    • 3D-printed lid in PETG
  • sara-bv2.0.04 months ago29.665h 7m

    One cold joint on the ground pad — needed flux and a bigger tip.

  • priyav2.0.05 months ago45.044h 3m

    USB enumeration failed until I added the 5.1k CC resistors. Check the errata.

  • kenjiv2.0.05 months ago38.473h 3m

    Had to swap the LDO — original is out of stock at LCSC.

  • junghyunv2.0.05 months ago31.723h 40m

    Running for three weeks continuously, no issues.

  • nilsv2.1.05 months ago27.943h 15m

    Had to swap the LDO — original is out of stock at LCSC.

  • priyav2.0.05 months ago39.332h 13m

    Substituted a cheaper mic; SNR is noticeably worse but usable.

  • obiv2.1.05 months ago30.882h 54m

    Printed the enclosure in PETG at 0.2mm, fits with no sanding.

  • theov2.0.05 months ago41.102h 26m

    Substituted a cheaper mic; SNR is noticeably worse but usable.

  • luciav2.1.05 months ago42.322h 14m

    One cold joint on the ground pad — needed flux and a bigger tip.